Search any CSR 2020 item by Keyword
ADD ADDITIONAL 5.35% PREMIUM ON ALL CSR-2020 ITEMS, THROUGH RATES AS WELL AS LABOUR RATES, INCLUDING PREMIUMS BEFORE A&C SLIP NO. 5.
Search Results
| CSR No. | Description | Unit | Plains | Sub Mountainous | Premium | |||
|---|---|---|---|---|---|---|---|---|
| Labour Rate | Through Rate | Labour Rate | Through Rate | Labour | Through | |||
| 35.01 (a) | Structural steel work for large gates having skin plate area exceeding 10.0 m², fabricated from rolled steel sections, plates, flats, angles, channels etc., including cutting, straightening, machining, drilling, edge preparation, shop welding, grinding, trial assembly, marking, transportation to site, hoisting, positioning and erection in true line, level and alignment, testing and commissioning complete, inclusive of all labour, consumables, incidentals and use of all tools and plants such as hydra crane, chain pulley block, welding sets, drilling machines, lathe and milling machines at the manufacturing workshop, but excluding hoisting arrangements permanently attached to the gate, wheel assemblies, rubber seals, centre drive units, gearing, shafts, bearings, motors, electrical components and painting/protective coating, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Embedment – Fixing of steel components to be embedded in concrete, such as IS plates, stiffener plates, ISMB/ISMC/ISST sections, anchor bolts, support plates, cleats and similar embedded parts, including accurate positioning, alignment and holding in true line and level during concreting, provision and removal of templates/jigs where required, coordination with concreting operations, and all labour, tools and incidentals, but excluding concrete, formwork and reinforcement, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. | qtl | 670 | 11652 | 737 | 11719 | ||
| 35.01 (b) | Structural steel work for large gates having skin plate area exceeding 10.0 m², fabricated from rolled steel sections, plates, flats, angles, channels etc., including cutting, straightening, machining, drilling, edge preparation, shop welding, grinding, trial assembly, marking, transportation to site, hoisting, positioning and erection in true line, level and alignment, testing and commissioning complete, inclusive of all labour, consumables, incidentals and use of all tools and plants such as hydra crane, chain pulley block, welding sets, drilling machines, lathe and milling machines at the manufacturing workshop, but excluding hoisting arrangements permanently attached to the gate, wheel assemblies, rubber seals, centre drive units, gearing, shafts, bearings, motors, electrical components and painting/protective coating, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Gate Leaf – All steel components forming the movable gate leaf, including IS plates, ISMC/ISMB sections, clamp plates, seal plates and similar members, including assembly, alignment and fitting of components to form the complete gate leaf, ensuring correct geometry, clearances and smooth operation, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. | qtl | 589 | 11014 | 648 | 11073 | ||
| 35.01 (c) | Structural steel work for large gates having skin plate area exceeding 10.0 m², fabricated from rolled steel sections, plates, flats, angles, channels etc., including cutting, straightening, machining, drilling, edge preparation, shop welding, grinding, trial assembly, marking, transportation to site, hoisting, positioning and erection in true line, level and alignment, testing and commissioning complete, inclusive of all labour, consumables, incidentals and use of all tools and plants such as hydra crane, chain pulley block, welding sets, drilling machines, lathe and milling machines at the manufacturing workshop, but excluding hoisting arrangements permanently attached to the gate, wheel assemblies, rubber seals, centre drive units, gearing, shafts, bearings, motors, electrical components and painting/protective coating, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Superstructure – All steel components of the supporting structure for lifting of gates, including IS plates, ISMB/ISMC sections, ISA angles, gusset plates, rib plates, chequered plates, railings and similar members, forming platforms, frames, walkways and supports, excluding lifting arrangements, hoisting machinery and mechanical/electrical equipment, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. | qtl | 511 | 11763 | 562 | 11814 | ||
| 35.02 (a) | Structural steel work for medium gates having skin plate area from 3.0 m² to 10.0 m², fabricated from rolled steel sections, plates, flats, angles, channels etc., including cutting, machining, drilling, shop welding, grinding, trial assembly, marking, transportation to site, hoisting, positioning and erection in true line, level and alignment, testing and commissioning, inclusive of all labour, consumables and use of tools and plants such as welding sets, drilling machines, lathe, milling machines, hydra crane, chain pulley block etc. at workshop and site, excluding hoisting arrangements, wheel assemblies, rubber seals, centre drive units, gearing, shafts, bearings, motors, electrical components and painting/protective coating, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Embedment – Fixing of steel components to be embedded in concrete, such as IS plates, stiffener plates, ISMB/ISMC/ISST sections, anchor bolts, support plates, cleats and similar embedded parts, including accurate positioning, alignment and holding in true line and level during concreting, provision and removal of templates/jigs where required, coordination with concreting operations and all labour, tools and incidentals, excluding concrete, formwork and reinforcement, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. | qtl | 1444 | 17071 | 1588 | 17215 | ||
| 35.02 (b) | Structural steel work for medium gates having skin plate area from 3.0 m² to 10.0 m², fabricated from rolled steel sections, plates, flats, angles, channels etc., including cutting, machining, drilling, shop welding, grinding, trial assembly, marking, transportation to site, hoisting, positioning and erection in true line, level and alignment, testing and commissioning, inclusive of all labour, consumables and use of tools and plants such as welding sets, drilling machines, lathe, milling machines, hydra crane, chain pulley block etc. at workshop and site, excluding hoisting arrangements, wheel assemblies, rubber seals, centre drive units, gearing, shafts, bearings, motors, electrical components and painting/protective coating, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Gate Leaf – All steel components forming the movable gate leaf, including IS plates, ISMC/ISMB sections, clamp plates, seal plates and similar members, assembled and fitted to form the complete gate leaf with correct geometry, alignment and clearances for smooth operation, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. | qtl | 2060 | 15123 | 2266 | 15329 | ||
| 35.02 (c) | Structural steel work for medium gates having skin plate area from 3.0 m² to 10.0 m², fabricated from rolled steel sections, plates, flats, angles, channels etc., including cutting, machining, drilling, shop welding, grinding, trial assembly, marking, transportation to site, hoisting, positioning and erection in true line, level and alignment, testing and commissioning, inclusive of all labour, consumables and use of tools and plants such as welding sets, drilling machines, lathe, milling machines, hydra crane, chain pulley block etc. at workshop and site, excluding hoisting arrangements, wheel assemblies, rubber seals, centre drive units, gearing, shafts, bearings, motors, electrical components and painting/protective coating, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Superstructure – All steel components of the supporting structure for lifting of gates, including IS plates, ISMB/ISMC sections, ISA angles, gusset plates, rib plates, chequered plates, railings and similar members, forming frames, platforms, walkways and supports, excluding lifting arrangements, hoisting machinery and mechanical/electrical equipment, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. | qtl | 1609 | 14090 | 1770 | 14251 | ||
| 35.03 (a) | Structural steel work for small gates having skin plate area less than 3.0 m², fabricated from rolled steel sections, plates, flats, angles, channels etc., including cutting, machining, drilling, shop welding, grinding, trial assembly, marking, transportation to site, hoisting, positioning and erection in true line, level and alignment, testing and commissioning, inclusive of all labour, consumables and use of tools and plants at workshop and site, excluding hoisting arrangements, wheel assemblies, rubber seals, centre drive units, gearing, shafts, bearings, motors, electrical components and painting/protective coating, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Embedment – Fixing of steel components to be embedded in concrete, such as IS plates, stiffener plates, ISMB/ISMC/ISST sections, anchor bolts, support plates, cleats and similar embedded parts, including accurate positioning, alignment and holding in true line and level during concreting, provision and removal of templates/jigs where required, coordination with concreting operations and all labour, tools and incidentals, excluding concrete, formwork and reinforcement, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Note: Item nos. 35.01, 35.02 and 35.03 to be used for new or fresh installation only. | qtl | 2530 | 22834 | 2783 | 23087 | ||
| 35.03 (b) | Structural steel work for small gates having skin plate area less than 3.0 m², fabricated from rolled steel sections, plates, flats, angles, channels etc., including cutting, machining, drilling, shop welding, grinding, trial assembly, marking, transportation to site, hoisting, positioning and erection in true line, level and alignment, testing and commissioning, inclusive of all labour, consumables and use of tools and plants at workshop and site, excluding hoisting arrangements, wheel assemblies, rubber seals, centre drive units, gearing, shafts, bearings, motors, electrical components and painting/protective coating, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Gate Leaf – All steel components forming the movable gate leaf, including IS plates, ISMC/ISMB sections, clamp plates, seal plates and similar members, assembled and fitted to form the complete gate leaf with correct geometry, alignment and clearances for smooth operation, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Note: Item nos. 35.01, 35.02 and 35.03 to be used for new or fresh installation only. | qtl | 3044 | 20690 | 3348 | 20994 | ||
| 35.03 (c) | Structural steel work for small gates having skin plate area less than 3.0 m², fabricated from rolled steel sections, plates, flats, angles, channels etc., including cutting, machining, drilling, shop welding, grinding, trial assembly, marking, transportation to site, hoisting, positioning and erection in true line, level and alignment, testing and commissioning, inclusive of all labour, consumables and use of tools and plants at workshop and site, excluding hoisting arrangements, wheel assemblies, rubber seals, centre drive units, gearing, shafts, bearings, motors, electrical components and painting/protective coating, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Superstructure – All steel components of the supporting structure for lifting of gates, including IS plates, ISMB/ISMC sections, ISA angles, gusset plates, rib plates, chequered plates, railings and similar members, forming frames, platforms, walkways and supports, excluding lifting arrangements, hoisting machinery and mechanical/electrical equipment, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Note: Item nos. 35.01, 35.02 and 35.03 to be used for new or fresh installation only. | qtl | 3602 | 26170 | 3962 | 26530 | ||
| 35.04 (a) | Spur / Helical gear for gate and gearing arrangement, fabricated from steel/CI as specified, including gear cutting (hobbing or shaping), machining, drilling, welding where required, keyway cutting, finishing, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants such as lathe, milling machine, hobbing machine and other gear-cutting equipment at manufacturing workshop, and hydra crane and handling equipment at site including testing and commissioning, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. 0-299 mm (O/d) (En-8/En-9 forging) | qtl | 11862 | 67028 | 13048 | 68214 | ||
| 35.04 (b) | Spur / Helical gear for gate and gearing arrangement, fabricated from steel/CI as specified, including gear cutting (hobbing or shaping), machining, drilling, welding where required, keyway cutting, finishing, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants such as lathe, milling machine, hobbing machine and other gear-cutting equipment at manufacturing workshop, and hydra crane and handling equipment at site including testing and commissioning, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. 300-649 mm O/d (Fabricated) | qtl | 8999 | 55072 | 9899 | 55972 | ||
| 35.04 (c) | Spur / Helical gear for gate and gearing arrangement, fabricated from steel/CI as specified, including gear cutting (hobbing or shaping), machining, drilling, welding where required, keyway cutting, finishing, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants such as lathe, milling machine, hobbing machine and other gear-cutting equipment at manufacturing workshop, and hydra crane and handling equipment at site including testing and commissioning, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. 650-999 mm O/d (Fabricated) | qtl | 7358 | 43551 | 8094 | 44287 | ||
| 35.04 (d) | Spur / Helical gear for gate and gearing arrangement, fabricated from steel/CI as specified, including gear cutting (hobbing or shaping), machining, drilling, welding where required, keyway cutting, finishing, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants such as lathe, milling machine, hobbing machine and other gear-cutting equipment at manufacturing workshop, and hydra crane and handling equipment at site including testing and commissioning, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. 1000 mm and Above O/d (Fabricated) | qtl | 5578 | 35572 | 6136 | 36130 | ||
| 35.04 (e) | Spur / Helical gear for gate and gearing arrangement, fabricated from steel/CI as specified, including gear cutting (hobbing or shaping), machining, drilling, welding where required, keyway cutting, finishing, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants such as lathe, milling machine, hobbing machine and other gear-cutting equipment at manufacturing workshop, and hydra crane and handling equipment at site including testing and commissioning, complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Alloy Steel Casting | qtl | 5441 | 48893 | 5985 | 49437 | ||
| 35.05 (a) | Bush type roller wheel/ pulley assembly for gate and gearing arrangement, fabricated from steel/CI including wheel, bush, shaft, spacers, pin and associated components, including cutting, machining, drilling, welding where required, boring and fitting of bush, finishing, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants such as lathe, milling machine and other machining equipment at manufacturing workshop, including testing and commissioning complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Upto 200 mm (O/d) | qtl | 46048 | 107649 | 50653 | 112254 | ||
| 35.05 (b) | Bush type roller wheel/ pulley assembly for gate and gearing arrangement, fabricated from steel/CI including wheel, bush, shaft, spacers, pin and associated components, including cutting, machining, drilling, welding where required, boring and fitting of bush, finishing, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants such as lathe, milling machine and other machining equipment at manufacturing workshop, including testing and commissioning complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Above 200 mm (O/d) | qtl | 20448 | 65411 | 22493 | 67456 | ||
| 35.06 (a) | Bearing type roller wheel/ pulley assembly for gate and gearing arrangement, fabricated from steel/CI including wheel, bearings, shaft, housing, spacers and associated components, including cutting, machining, drilling, welding where required, boring, fitting of bearings, finishing, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants such as lathe, milling machine, hobbing machine and other machining equipment at manufacturing workshop, including testing and commissioning complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Upto 350 mm (O/d) Note: Item Nos. 35.05 and 35.06 may also be utilized for repair works, based on the applicable weight of the components to be repaired and reinstalled. | qtl | 2418 | 48497 | 2660 | 48739 | ||
| 35.06 (b) | Bearing type roller wheel/ pulley assembly for gate and gearing arrangement, fabricated from steel/CI including wheel, bearings, shaft, housing, spacers and associated components, including cutting, machining, drilling, welding where required, boring, fitting of bearings, finishing, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants such as lathe, milling machine, hobbing machine and other machining equipment at manufacturing workshop, including testing and commissioning complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Above 350 mm (O/d) Note: Item Nos. 35.05 and 35.06 may also be utilized for repair works, based on the applicable weight of the components to be repaired and reinstalled. | qtl | 16084 | 69994 | 17692 | 71602 | ||
| 35.07 (a) | Supply and installation of housing cover assembly with worm and worm wheel assembly, including shaft, handle with triple-start internal threading for spindle and all associated components including spindle , for gate and gearing arrangement, including cutting, machining, threading, drilling, fixing with nuts and bolts, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants and machinery required at workshop and site, including testing and commissioning complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. (Rate applicable for a set of 2 Nos. hoist assemblies per gate.) up to 1.50 ton capacity. Note: For single hoist assembly on one gate the rate of the item no. 35.7 can be halved. | Job | 54802 | 300762 | 60282 | 306242 | ||
| 35.07 (b) | Supply and installation of housing cover assembly with worm and worm wheel assembly, including shaft, handle with triple-start internal threading for spindle and all associated components including spindle , for gate and gearing arrangement, including cutting, machining, threading, drilling, fixing with nuts and bolts, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants and machinery required at workshop and site, including testing and commissioning complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. (Rate applicable for a set of 2 Nos. hoist assemblies per gate.) from 1.5 to 2.50 ton capacity. Note: For single hoist assembly on one gate the rate of the item no. 35.7 can be halved. | Job | 56516 | 349661 | 62168 | 355313 | ||
| 35.08 | Supply and installation of rope drum hoist assembly (worm type) with worm and worm wheel assembly, shafts, handle and rope drums up to 300 mm diameter, for gate and gearing arrangement, including cutting, machining, threading, drilling, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants and machinery required at workshop and site, excluding wire ropes and nuts & bolts, including testing and commissioning complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Note: The diameter of the rope drum in the worm-type rope drum hoist assembly shall not exceed 300 mm. For rope drums diameter more than 300 mm, item no. 35.09 shall be used. | Job | 54802 | 351457 | 60282 | 356937 | ||
| 35.09 (a) | Supply and installation of rope drum hoist assembly with spur pinion and spur gear wheel assembly, including shafts, handle and rope drum, for gate and gearing arrangement, including cutting, machining, threading, drilling, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants and machinery required at workshop and site, excluding wire ropes and nuts & bolts, including testing and commissioning complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Rope drums upto 300 MM dia | Job | 54802 | 390526 | 60282 | 396006 | ||
| 35.09 (b) | Supply and installation of rope drum hoist assembly with spur pinion and spur gear wheel assembly, including shafts, handle and rope drum, for gate and gearing arrangement, including cutting, machining, threading, drilling, trial assembly, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants and machinery required at workshop and site, excluding wire ropes and nuts & bolts, including testing and commissioning complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. Rope drum from 301 mm to 400 mm dia | Job | 54802 | 540343 | 60282 | 545823 | ||
| 35.10 | Supply and installation of rack and pinion gearing arrangement with worm and worm wheel, including shafts, housing and two rack-and-pinion assemblies, for gate operation, including cutting, machining, threading, drilling, trial assembly, fixing with nuts and bolts, transportation to site, hoisting and erection in position, inclusive of all labour, consumables and use of all tools and plants and machinery required at workshop and site, including testing and commissioning complete in all respects as per approved drawings, specifications and directions of the Engineer-in-Charge. (Rate applicable for a set of 1 No. assembly per gate.) | Job | 54802 | 590730 | 60282 | 596210 | ||
| 35.11 | Supply and fixing of M.S. spindle for gate hoisting and gearing arrangement, including cutting to required length, threading, machining, fixing with nuts, bolts, washers, keys, couplings etc., hoisting, erecting, aligning and fixing in position, including cost of all materials, labour, tools & plants, machinery, handling, loading, unloading and all incidental charges, including testing and commissioning complete in all respects, as per approved drawings and directions of Engineer-in-Charge. | qtl | 12962 | 86257 | 14258 | 87553 | ||
| 35.12 | Structural steel repair work in angles, tees, channels, flats, pipes, girders, plates, etc. of gate and gearing arrangement on canal/drainage system, including cutting to required size, drilling, fixing of all gusset plates, welding, providing and fixing bolts, nuts and rivets, hoisting, erecting and fixing in position at site, including cost of all materials, labour, tools & plants, machinery and equipment required, complete in all respects, as per approved drawings and directions of Engineer-in-Charge. | qtl | 6223.15 | 12652.38 | 6845 | 13274.7 | ||
| 35.13 | Replacement of gunmetal bush, including removing the old/damaged bush, supplying, assembling and fixing the new bush in position, including all labour, tools & plants, handling and incidental charges, complete in all respects, to the entire satisfaction of Engineer-in-Charge. | kg | 830.92 | 3919.26 | 914.01 | 4002.35 | ||
| 35.14 (a) | Providing and fixing in position hollow bulb seal, including drilling, reaming, boring, preparation of surface, and providing and fixing stainless steel nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 100x44x12 mm | m | 321.97 | 3321.09 | 354.17 | 3353.29 | ||
| 35.14 (b) | Providing and fixing in position hollow bulb seal, including drilling, reaming, boring, preparation of surface, and providing and fixing stainless steel nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 120x44x20 mm | m | 321.97 | 4176.49 | 354.17 | 4208.69 | ||
| 35.14 (c) | Providing and fixing in position hollow bulb seal, including drilling, reaming, boring, preparation of surface, and providing and fixing stainless steel nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 57x22x8 mm | m | 160.99 | 833.02 | 177.09 | 849.12 | ||
| 35.15 (a) | Providing and fixing in position hollow bulb seal, including drilling, reaming, boring, preparation of surface, and providing and fixing galvanized nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 100x44x12 mm | m | 322 | 2927 | 354 | 2959 | ||
| 35.15 (b) | Providing and fixing in position hollow bulb seal, including drilling, reaming, boring, preparation of surface, and providing and fixing galvanized nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 120x44x20 mm | m | 321.97 | 4493.17 | 354.17 | 4525.37 | ||
| 35.15 (c) | Providing and fixing in position hollow bulb seal, including drilling, reaming, boring, preparation of surface, and providing and fixing galvanized nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 57x22x8 mm | m | 160.99 | 693.01 | 177.09 | 709.11 | ||
| 35.16 (a) | Providing and fixing in position wedge seal, including drilling, reaming, boring, preparation of surface, and providing and fixing stainless steel nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 75 mm dia x 12 mm thickness | m | 241.48 | 1678.31 | 265.63 | 1702.46 | ||
| 35.16 (b) | Providing and fixing in position wedge seal, including drilling, reaming, boring, preparation of surface, and providing and fixing stainless steel nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 80 mm dia x 12 mm thickness | m | 483 | 2025 | 531 | 2073 | ||
| 35.16 (c) | Providing and fixing in position wedge seal, including drilling, reaming, boring, preparation of surface, and providing and fixing stainless steel nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 120 mm dia x 10 mm thickness | m | 563 | 2392 | 619 | 2448 | ||
| 35.16 (d) | Providing and fixing in position wedge seal, including drilling, reaming, boring, preparation of surface, and providing and fixing stainless steel nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 120 mm dia x 20 mm thickness | m | 644 | 3388 | 708 | 3452 | ||
| 35.17 (a) | Providing and fixing in position wedge seal, including drilling, reaming, boring, preparation of surface, and providing and fixing G.I. nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 75 mm dia x 12 mm thickness | m | 241 | 1284 | 265 | 1308 | ||
| 35.17 (b) | Providing and fixing in position wedge seal, including drilling, reaming, boring, preparation of surface, and providing and fixing G.I. nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 80 mm dia x 12 mm thickness | m | 322 | 1426 | 354 | 1458 | ||
| 35.17 (c) | Providing and fixing in position wedge seal, including drilling, reaming, boring, preparation of surface, and providing and fixing G.I. nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 120 mm dia x 10 mm thickness | m | 563 | 1899 | 619 | 1955 | ||
| 35.17 (d) | Providing and fixing in position wedge seal, including drilling, reaming, boring, preparation of surface, and providing and fixing G.I. nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. 120 mm dia x 20 mm thickness | m | 644 | 2917 | 708 | 2981 | ||
| 35.18 | Providing and fixing in position pipe seal of 75 mm diameter and 8 mm thickness, including drilling, reaming, boring, preparation of surface, and providing and fixing stainless steel nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. | m | 161 | 2723 | 177 | 2739 | ||
| 35.19 | Providing and fixing in position pipe seal of 75 mm diameter and 8 mm thickness, including drilling, reaming, boring, preparation of surface, and providing and fixing galvanized nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. | m | 241 | 2256 | 265 | 2280 | ||
| 35.20 | Providing and fixing in position angle rubber seal of size 90 × 55 × 16 mm, including drilling, reaming, boring, preparation of surface, and providing and fixing stainless steel nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. | m | 260 | 2496 | 286 | 2522 | ||
| 35.21 | Providing and fixing in position angle rubber seal of size 90 × 55 × 16 mm, including drilling, reaming, boring, preparation of surface, and providing and fixing galvanized nuts and bolts, complete in all respects, as per approved drawings and to the entire satisfaction of Engineer-in-Charge. | m | 260 | 2102 | 286 | 2128 | ||
| 35.22 | Removing / dismantling of damaged old rubber seal, including removing nuts and bolts, clamps and stacking the dismantled material within 50 metres lead, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. | m | 254 | 499 | 279 | 524 | ||
| 35.23 (a) | Providing and fixing in position new steel wire rope with steel core, including lifting by chain pulley or crane, cutting to required length, linking/anchoring with gate and hoisting mechanism for smooth and balanced operation, oiling and greasing, complete in all respects, conforming to IS: 2266, construction 6 × 37, as per specifications and to the entire satisfaction of Engineer-in-Charge. 0-10 mm dia | m | 34 | 416 | 37 | 419 | ||
| 35.23 (b) | Providing and fixing in position new steel wire rope with steel core, including lifting by chain pulley or crane, cutting to required length, linking/anchoring with gate and hoisting mechanism for smooth and balanced operation, oiling and greasing, complete in all respects, conforming to IS: 2266, construction 6 × 37, as per specifications and to the entire satisfaction of Engineer-in-Charge. 11-20 mm dia | m | 52 | 1026 | 57 | 1031 | ||
| 35.23 (c) | Providing and fixing in position new steel wire rope with steel core, including lifting by chain pulley or crane, cutting to required length, linking/anchoring with gate and hoisting mechanism for smooth and balanced operation, oiling and greasing, complete in all respects, conforming to IS: 2266, construction 6 × 37, as per specifications and to the entire satisfaction of Engineer-in-Charge. 21-30 mm dia | m | 65 | 2239 | 72 | 2246 | ||
| 35.23 (d) | Providing and fixing in position new steel wire rope with steel core, including lifting by chain pulley or crane, cutting to required length, linking/anchoring with gate and hoisting mechanism for smooth and balanced operation, oiling and greasing, complete in all respects, conforming to IS: 2266, construction 6 × 37, as per specifications and to the entire satisfaction of Engineer-in-Charge. 31-40 mm dia | m | 78 | 3040 | 86 | 3048 | ||
| 35.23 (e) | Providing and fixing in position new steel wire rope with steel core, including lifting by chain pulley or crane, cutting to required length, linking/anchoring with gate and hoisting mechanism for smooth and balanced operation, oiling and greasing, complete in all respects, conforming to IS: 2266, construction 6 × 37, as per specifications and to the entire satisfaction of Engineer-in-Charge. 41-50 mm dia | m | 104 | 4031 | 114 | 4041 | ||
| 35.23 (f) | Providing and fixing in position new steel wire rope with steel core, including lifting by chain pulley or crane, cutting to required length, linking/anchoring with gate and hoisting mechanism for smooth and balanced operation, oiling and greasing, complete in all respects, conforming to IS: 2266, construction 6 × 37, as per specifications and to the entire satisfaction of Engineer-in-Charge. more than 50 mm up to 60 mm dia | m | 130 | 4856 | 143 | 4869 | ||
| 35.24 | Dismantling of damaged wire rope, including de-linking from gate and hoisting mechanism, with provision of crane and/or chain pulley block for safely supporting the gate during operation, making coils/rolls of dismantled rope, and stacking the same within a lead of 50 metres, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. | qtl | 2161 | 10118 | 2377 | 10334 | ||
| 35.25 | Supply, fabrication and installation of rolling chain assembly of LUS gates for gate and gearing arrangement, including cutting, machining, welding, drilling, fixing, hoisting and erection in position, complete in all respects, including cost of all labour, materials, tools and plants, machinery such as hydra crane at site and lathe machine, milling machine or hobbing machine at manufacturing works, complete to the entire satisfaction of the Engineer-in-Charge. | qtl | 5644 | 35971 | 6208 | 36535 | ||
| 35.26 | Dismantling of damaged rolling chain assembly of LUS gates, including stacking of dismantled material within a lead of 50 metres, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. | qtl | 810 | 6821 | 891 | 6902 | ||
| 35.27 (a) | Overhauling of gates and gearing arrangement of large gates, including cleaning, lubrication/greasing of all moving parts, checking, tightening and replacement of worn-out fasteners where required, alignment, minor adjustments, trial operation and making the system smooth and functional, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. Large gates having skin plate area exceeding 10.0 m² | Job | 4703 | 35452 | 5173 | 35922 | ||
| 35.27 (b) | Overhauling of gates and gearing arrangement of large gates, including cleaning, lubrication/greasing of all moving parts, checking, tightening and replacement of worn-out fasteners where required, alignment, minor adjustments, trial operation and making the system smooth and functional, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. Medium gates having skin plate area between 3.0 to 10.0 m² | Job | 3136 | 24550 | 3450 | 24864 | ||
| 35.27 (c) | Overhauling of gates and gearing arrangement of large gates, including cleaning, lubrication/greasing of all moving parts, checking, tightening and replacement of worn-out fasteners where required, alignment, minor adjustments, trial operation and making the system smooth and functional, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. Small gates having skin plate area less then 3.0 m² | Job | 1331 | 17366 | 1464 | 17499 | ||
| 35.28 | Greasing of gates and gearing arrangements including supply of synthetic hetiv grease complete in all respects and to the entire satisfaction of the Engineer-in-Charge. | kg | 55 | 956 | 61 | 962 | ||
| 35.29 | Oiling of gearing arrangements including supply of lubricating oil/ mobile oil complete in all respects and to the entire satisfaction of the Engineer-in-Charge. | ltr | 27 | 280 | 30 | 283 | ||
| 35.30 (a) | Removal of gate leaf for repair purposes, including dismantling, hoisting, lowering and shifting to a safe place, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. FOR SKIN PLATE AREA > 10 SQM | Job | 2012 | 13254 | 2213 | 13455 | ||
| 35.30 (b) | Removal of gate leaf for repair purposes, including dismantling, hoisting, lowering and shifting to a safe place, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. FOR SKIN PLATE AREA 3 - 10 SQM | Job | 1610 | 10041 | 1771 | 10202 | ||
| 35.30 (c) | Removal of gate leaf for repair purposes, including dismantling, hoisting, lowering and shifting to a safe place, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. FOR SKIN PLATE AREA <3 SQM | Job | 1207 | 7218 | 1328 | 7339 | ||
| 35.31 (a) | Installation of gate leaf only, after repair, as required, including hoisting, lowering, assembling, alignment, testing and commissioning of gate, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. (Note: The repair charges are not included in this item) FOR SKIN PLATE AREA > 10 SQM | Job | 4830 | 16851 | 5313 | 17334 | ||
| 35.31 (b) | Installation of gate leaf only, after repair, as required, including hoisting, lowering, assembling, alignment, testing and commissioning of gate, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. (Note: The repair charges are not included in this item) FOR SKIN PLATE AREA 3 - 10 SQM | Job | 3220 | 14462 | 3542 | 14784 | ||
| 35.31 (c) | Installation of gate leaf only, after repair, as required, including hoisting, lowering, assembling, alignment, testing and commissioning of gate, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. (Note: The repair charges are not included in this item) FOR SKIN PLATE AREA <3 SQM | Job | 2012 | 10833 | 2213 | 11034 | ||
| 35.32 | Dismantling, Removal and re-installation of gate parts (excluding gate leaf components such as gate frame stiffeners, skin plates, clamp plates, rollers, seals, etc.) for replacement/repair purposes, as required, including hoisting, re-assembling, lowering into position, proper alignment, testing and commissioning of gate and gearing arrangements, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. Note: Rate shall be based on the weight of the assembly removed and re-installed. Replacement of any defective part shall be measured and paid separately. | qtl | 2817 | 5215 | 3099 | 5497 | ||
| 35.33 | Supply and fixing of galvanized nuts and bolts of required size and length, including washers, threading, tightening, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. | kg | 55 | 188 | 61 | 194 | ||
| 35.34 | Supply and fixing of Stainless Steel nuts and bolts of required size and length, including washers, threading, tightening, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. | kg | 55 | 1239 | 61 | 1245 | ||
| 35.35 | Supply and fixing of Grease Nipple of required size including threading, tightening, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. | No. | 33 | 51 | 36 | 54 | ||
| 35.36 (a) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 30 MM, 6206 No. | No. | 389 | 1138 | 428 | 1177 | ||
| 35.36 (b) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 35 MM, 6207 No. | No. | 389 | 1186 | 428 | 1225 | ||
| 35.36 (c) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 40 MM, 6208 No. | No. | 583 | 1463 | 641 | 1521 | ||
| 35.36 (d) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 45 MM. 6209 No. | No. | 583 | 1532 | 641 | 1590 | ||
| 35.36 (e) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 50 MM, 6210 No. | No. | 777 | 1981 | 855 | 2059 | ||
| 35.36 (f) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 55 MM, 6211 No. | No. | 777 | 2137 | 855 | 2215 | ||
| 35.36 (g) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 60 MM, 6212 No. | No. | 1166 | 2932 | 1283 | 3049 | ||
| 35.36 (h) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 65 MM, 6213 No. | No. | 1166 | 3127 | 1283 | 3244 | ||
| 35.36 (i) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 70 MM, 6214 No. | No. | 1554 | 3976 | 1709 | 4131 | ||
| 35.36 (j) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 75 MM, 6215 No. | No. | 1554 | 4056 | 1709 | 4211 | ||
| 35.36 (k) | Providing and fixing in position new Ball Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Ball Bearing FOR SHAFT 80 MM, 6216 No. | No. | 1554 | 4758 | 1709 | 4913 | ||
| 35.37 (a) | Providing and fixing in position new Spherical Roller Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Spherical roller bearing for shaft 60 MM, 22212 No. | No. | 1166 | 5537 | 1283 | 5654 | ||
| 35.37 (b) | Providing and fixing in position new Spherical Roller Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Spherical roller bearing for shaft 70 MM, 22214 No. | No. | 1554 | 7191 | 1709 | 7346 | ||
| 35.37 (c) | Providing and fixing in position new Spherical Roller Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Spherical roller bearing for shaft 75 MM, 22215 No. | No. | 1554 | 7498 | 1709 | 7653 | ||
| 35.37 (d) | Providing and fixing in position new Spherical Roller Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Spherical roller bearing for shaft 80 MM, 22216 No. | No. | 1554 | 7864 | 1709 | 8019 | ||
| 35.37 (e) | Providing and fixing in position new Spherical Roller Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Spherical roller bearing for shaft 100 MM, 22220 No. | No. | 1943 | 12541 | 2137 | 12735 | ||
| 35.37 (f) | Providing and fixing in position new Spherical Roller Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Spherical roller bearing for shaft 110 MM, 22222 No. | No. | 1943 | 13504 | 2137 | 13698 | ||
| 35.37 (g) | Providing and fixing in position new Spherical Roller Bearing of approved make and specified size for gate and gearing arrangement, including lifting by chain pulley, fitting on shaft/housing, alignment, packing, lubrication with hetiv grease, testing for smooth and balanced operation and all incidental works, complete in all respects, conforming to IS specifications and as per approved drawings, specifications and to the entire satisfaction of the Engineer-in-Charge. Spherical roller bearing for shaft 120 MM, 22224 No. | No. | 1943 | 18678 | 2137 | 18872 | ||
| 35.38 (a) | Removing the existing bearing bracket and providing, supplying and fixing in position of new bearing bracket including necessary nuts, bolts, washers, alignment and fitting with the existing mechanism, testing and commissioning, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. BEARING BRACKET FOR SHAFT 50 MM | Job | 1094 | 2079 | 1203 | 2188 | ||
| 35.38 (b) | Removing the existing bearing bracket and providing, supplying and fixing in position of new bearing bracket including necessary nuts, bolts, washers, alignment and fitting with the existing mechanism, testing and commissioning, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. BEARING BRACKET FOR SHAFT 55 MM | Job | 1094 | 2047 | 1203 | 2156 | ||
| 35.38 (c) | Removing the existing bearing bracket and providing, supplying and fixing in position of new bearing bracket including necessary nuts, bolts, washers, alignment and fitting with the existing mechanism, testing and commissioning, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. BEARING BRACKET FOR SHAFT 60 MM | Job | 1367 | 2638 | 1504 | 2775 | ||
| 35.38 (d) | Removing the existing bearing bracket and providing, supplying and fixing in position of new bearing bracket including necessary nuts, bolts, washers, alignment and fitting with the existing mechanism, testing and commissioning, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. BEARING BRACKET FOR SHAFT 65 MM | Job | 1367 | 2806 | 1504 | 2943 | ||
| 35.38 (e) | Removing the existing bearing bracket and providing, supplying and fixing in position of new bearing bracket including necessary nuts, bolts, washers, alignment and fitting with the existing mechanism, testing and commissioning, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. BEARING BRACKET FOR SHAFT 70 MM | Job | 1641 | 3063 | 1805 | 3227 | ||
| 35.38 (f) | Removing the existing bearing bracket and providing, supplying and fixing in position of new bearing bracket including necessary nuts, bolts, washers, alignment and fitting with the existing mechanism, testing and commissioning, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. BEARING BRACKET FOR SHAFT 75 MM | Job | 1641 | 3293 | 1805 | 3457 | ||
| 35.39 (a) | Removing the existing electromagnetic (E.M.) brake and providing, supplying, installation and fixing in position of new electromagnetic brake at site including necessary mounting arrangement, wiring connections, nuts, bolts, washers, alignment, testing and commissioning, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. Electro Magnetic Brake ( DRUM SIZE DIA UPTO 150 MM ) | Job | 2188 | 25906 | 2407 | 26125 | ||
| 35.39 (b) | Removing the existing electromagnetic (E.M.) brake and providing, supplying, installation and fixing in position of new electromagnetic brake at site including necessary mounting arrangement, wiring connections, nuts, bolts, washers, alignment, testing and commissioning, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. Electro Magnetic Brake ( DRUM SIZE DIA UPTO 200 MM ) | Job | 2188 | 29146 | 2407 | 29365 | ||
| 35.40 (a) | Removing the existing Plummer block and providing, supplying and fixing in position of new Plummer block (Make: SKF / NBC) as per approved list including necessary dismantling, bolts, nuts, washers, alignment, lubrication and fitting with the existing shaft/mechanism, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. PLUMMER BLOCK FOR SHAFT 50 MM, 6210 No. | Job | 1568 | 3760 | 1725 | 3917 | ||
| 35.40 (b) | Removing the existing Plummer block and providing, supplying and fixing in position of new Plummer block (Make: SKF / NBC) as per approved list including necessary dismantling, bolts, nuts, washers, alignment, lubrication and fitting with the existing shaft/mechanism, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. PLUMMER BLOCK FOR SHAFT 55 MM, 6211 No. | Job | 1568 | 3838 | 1725 | 3995 | ||
| 35.40 (c) | Removing the existing Plummer block and providing, supplying and fixing in position of new Plummer block (Make: SKF / NBC) as per approved list including necessary dismantling, bolts, nuts, washers, alignment, lubrication and fitting with the existing shaft/mechanism, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. PLUMMER BLOCK FOR SHAFT 60 MM, 6212 No. | Job | 1568 | 4214 | 1725 | 4371 | ||
| 35.40 (d) | Removing the existing Plummer block and providing, supplying and fixing in position of new Plummer block (Make: SKF / NBC) as per approved list including necessary dismantling, bolts, nuts, washers, alignment, lubrication and fitting with the existing shaft/mechanism, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. PLUMMER BLOCK FOR SHAFT 65 MM, 6213 No. | Job | 1960 | 5243 | 2156 | 5439 | ||
| 35.40 (e) | Removing the existing Plummer block and providing, supplying and fixing in position of new Plummer block (Make: SKF / NBC) as per approved list including necessary dismantling, bolts, nuts, washers, alignment, lubrication and fitting with the existing shaft/mechanism, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. PLUMMER BLOCK FOR SHAFT 70 MM, 6214 No. | Job | 1960 | 5657 | 2156 | 5853 | ||
| 35.40 (f) | Removing the existing Plummer block and providing, supplying and fixing in position of new Plummer block (Make: SKF / NBC) as per approved list including necessary dismantling, bolts, nuts, washers, alignment, lubrication and fitting with the existing shaft/mechanism, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. PLUMMER BLOCK FOR SHAFT 75 MM, 6215 No. | Job | 2352 | 6697 | 2587 | 6932 | ||
| 35.40 (g) | Removing the existing Plummer block and providing, supplying and fixing in position of new Plummer block (Make: SKF / NBC) as per approved list including necessary dismantling, bolts, nuts, washers, alignment, lubrication and fitting with the existing shaft/mechanism, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. PLUMMER BLOCK FOR SHAFT 80 MM, 6216 No. | Job | 2352 | 7216 | 2587 | 7451 | ||
| 35.40 (h) | Removing the existing Plummer block and providing, supplying and fixing in position of new Plummer block (Make: SKF / NBC) as per approved list including necessary dismantling, bolts, nuts, washers, alignment, lubrication and fitting with the existing shaft/mechanism, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. PLUMMER BLOCK for shaft 100 MM, 6220 No. | Job | 3136 | 13043 | 3450 | 13357 | ||
| 35.40 (i) | Removing the existing Plummer block and providing, supplying and fixing in position of new Plummer block (Make: SKF / NBC) as per approved list including necessary dismantling, bolts, nuts, washers, alignment, lubrication and fitting with the existing shaft/mechanism, complete in all respects and to the entire satisfaction of the Engineer-in-Charge. PLUMMER BLOCK for shaft 120 MM, 6224 No. | Job | 3136 | 15285 | 3450 | 15599 | ||
| 35.41 (a) | Casting as per IS specifications and grade including cost of material and framework complete in all respects and to entire satisfaction of Engineer-in-charge. Alloy steel casting | qtl | 415 | 14217 | 457 | 14259 | ||
| 35.41 (b) | Casting as per IS specifications and grade including cost of material and framework complete in all respects and to entire satisfaction of Engineer-in-charge. Cast Iron Graded | qtl | 415 | 12503 | 457 | 12545 | ||
| 35.41 (c) | Casting as per IS specifications and grade including cost of material and framework complete in all respects and to entire satisfaction of Engineer-in-charge. Brass | qtl | 6633 | 235301 | 7296 | 235964 | ||
| 35.41 (d) | Casting as per IS specifications and grade including cost of material and framework complete in all respects and to entire satisfaction of Engineer-in-charge. Bronze | qtl | 6633 | 335163 | 7296 | 335826 | ||
| 35.41 (e) | Casting as per IS specifications and grade including cost of material and framework complete in all respects and to entire satisfaction of Engineer-in-charge. Gunmetal | kg | 166 | 2215 | 183 | 2232 | ||
| 35.42 | Steel forging in EN-8 or EN-9 steel, including cost of material, forging, finishing, and all incidental operations, conforming to relevant IS specifications and grade, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. | qtl | 829 | 15303 | 912 | 15386 | ||
| 35.43 | Machining and finishing of any part to the required shape and size, including turning, facing, drilling, milling and grinding, as required, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. | qtl | 1094 | 4314 | 1203 | 4423 | ||
| 35.44 (a) | Threading of steel or any other metal, including cutting / chasing of threads by machine or by hand, cleaning, application of cutting oil, and making threads accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. External threading up to 20 mm dia Note: The length of threading shall be measured as the actual linear length of the threaded portion along the axis of the component, irrespective of number of threads or pitch. | rcm | 5 | 16 | 6 | 17 | ||
| 35.44 (b) | Threading of steel or any other metal, including cutting / chasing of threads by machine or by hand, cleaning, application of cutting oil, and making threads accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. External threading above 20 mm and up to 40 mm diameter Note: The length of threading shall be measured as the actual linear length of the threaded portion along the axis of the component, irrespective of number of threads or pitch. | rcm | 8 | 24 | 9 | 25 | ||
| 35.44 (c) | Threading of steel or any other metal, including cutting / chasing of threads by machine or by hand, cleaning, application of cutting oil, and making threads accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. External threading above 40 mm and up to 75 mm diameter Note: The length of threading shall be measured as the actual linear length of the threaded portion along the axis of the component, irrespective of number of threads or pitch. | rcm | 11 | 43 | 12 | 44 | ||
| 35.44 (d) | Threading of steel or any other metal, including cutting / chasing of threads by machine or by hand, cleaning, application of cutting oil, and making threads accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. External threading above 75 mm diameter Note: The length of threading shall be measured as the actual linear length of the threaded portion along the axis of the component, irrespective of number of threads or pitch. | rcm | 14 | 62 | 15 | 63 | ||
| 35.44 (e) | Threading of steel or any other metal, including cutting / chasing of threads by machine or by hand, cleaning, application of cutting oil, and making threads accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. Internal threading up to 20 mm diameter Note: The length of threading shall be measured as the actual linear length of the threaded portion along the axis of the component, irrespective of number of threads or pitch. | rcm | 11 | 40 | 12 | 41 | ||
| 35.44 (f) | Threading of steel or any other metal, including cutting / chasing of threads by machine or by hand, cleaning, application of cutting oil, and making threads accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. Internal threading above 20 mm and up to 40 mm diameter Note: The length of threading shall be measured as the actual linear length of the threaded portion along the axis of the component, irrespective of number of threads or pitch. | rcm | 14 | 57 | 15 | 58 | ||
| 35.44 (g) | Threading of steel or any other metal, including cutting / chasing of threads by machine or by hand, cleaning, application of cutting oil, and making threads accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. Internal threading above 40 mm and up to 75 mm diameter Note: The length of threading shall be measured as the actual linear length of the threaded portion along the axis of the component, irrespective of number of threads or pitch. | rcm | 16 | 75 | 18 | 77 | ||
| 35.44 (h) | Threading of steel or any other metal, including cutting / chasing of threads by machine or by hand, cleaning, application of cutting oil, and making threads accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. Internal threading above 75 mm diameter Note: The length of threading shall be measured as the actual linear length of the threaded portion along the axis of the component, irrespective of number of threads or pitch. | rcm | 25 | 105 | 28 | 108 | ||
| 35.45 (a) | Teeth cutting on steel or any other metal, including cutting by machine, cleaning, application of cutting oil and making teeth accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. 6 dp | tooth per cm thickness of wheel | 4 | 9 | 4 | 9 | ||
| 35.45 (b) | Teeth cutting on steel or any other metal, including cutting by machine, cleaning, application of cutting oil and making teeth accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. 8 dp | tooth per cm thickness of wheel | 4 | 9 | 4 | 9 | ||
| 35.45 (c) | Teeth cutting on steel or any other metal, including cutting by machine, cleaning, application of cutting oil and making teeth accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. 10 dp | tooth per cm thickness of wheel | 4 | 7 | 4 | 7 | ||
| 35.45 (d) | Teeth cutting on steel or any other metal, including cutting by machine, cleaning, application of cutting oil and making teeth accurate and concentric as per approved drawings and specifications, complete in all respects, and to the entire satisfaction of Engineer-in-Charge. 12 dp | tooth per cm thickness of wheel | 3 | 6 | 3 | 6 | ||
| 35.46 (a) (i) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. 0 -10 mm dia Thickness of first 5 mm | mm | 1.3 | 3 | 1.43 | 3 | ||
| 35.46 (a) (ii) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. 0 -10 mm dia For thickness of every additional 5 mm | mm | 0.26 | 1 | 0.29 | 1.03 | ||
| 35.46 (b) (i) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. 11 - 20 mm dia Thickness of first 5 mm | mm | 1.3 | 4 | 1.43 | 4 | ||
| 35.46 (b) (ii) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. 11 - 20 mm dia For thickness of every additional 5 mm | mm | 0.26 | 1 | 0.29 | 1.03 | ||
| 35.46 (c) (i) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. 21 - 30 mm dia Thickness of first 5 mm | mm | 2.16 | 6 | 2.38 | 6 | ||
| 35.46 (c) (ii) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. 21 - 30 mm dia For thickness of every additional 5 mm | mm | 0.43 | 1 | 0.47 | 1 | ||
| 35.46 (d) (i) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. 31 - 40 mm dia Thickness of first 5 mm | mm | 2.6 | 9 | 2.86 | 9 | ||
| 35.46 (d) (ii) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. 31 - 40 mm dia For thickness of every additional 5 mm | mm | 0.52 | 2 | 0.57 | 2.05 | ||
| 35.46 (e) (i) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. 41 - 50 mm dia Thickness of first 5 mm | mm | 2.6 | 11 | 2.86 | 11 | ||
| 35.46 (e) (ii) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. 41 - 50 mm dia For thickness of every additional 5 mm | mm | 0.52 | 2 | 0.57 | 2 | ||
| 35.46 (f) (i) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. Above 50 mm dia Thickness of first 5 mm | No. | 3.46 | 16 | 3.81 | 16 | ||
| 35.46 (f) (ii) | Drilling/ boring/ reaming hole including complete in all respects and to the entire satisfaction of Engineer-in-charge. Above 50 mm dia For thickness of every additional 5 mm | No. | 0.69 | 3 | 0.76 | 3 | ||
| 35.47 | Sand blasting of rusted steel gates/steel surfaces for removal of rust, scale and old paint up to SA-2.5 standard using abrasive media with compressed air operated sand blasting machine, including supply of abrasives, scaffolding or staging, labour, machinery, safety equipment, collection and disposal of debris, and complete surface preparation before painting, complete in all respects as directed by the Engineer-in-Charge. | sqm | 376 | 1838 | 414 | 1876 | ||
| 35.48 | Supply & installation of Bevel Gearbox having gear ratio 1:1, fitted with straight/spiral bevel gears, comprising one input shaft and two co-axial output shafts, all suitably keyed for coupling purposes, complete with mounting base, foundation bolts, lubrication arrangement and all other necessary accessories required for satisfactory operation. | Job | 33898 | 33898 | ||||
| 35.49 | Providing & assembling of Manual Shifting Arrangement/Jaw Clutch Assembly for manual override operation, including all necessary components, properly aligned and fitted for smooth and reliable functioning under all operating conditions. | Job | 5084 | 5084 | ||||
